Diferencias

Muestra las diferencias entre dos versiones de la página.

--- doc:tec:print3d:orca:gcode:inicio [2025/03/21 12:57] – creado euloxio
+++ doc:tec:print3d:orca:gcode:inicio [Fecha desconocida] (actual) – editor externo (Fecha desconocida) 127.0.0.1
@@ Línea 1: / Línea 1: @@
+====== Orca - Start/End gcode ======
+<WRAP center round help 80%>
+  * [[https://www.hta3d.com/es/blog/super-slicer-probablemente-el-mejor-programa-para-generar-gcode-para-tu-impersora-3d?srsltid=AfmBOooo8vHrbz6MNF8rbxJPqroCcuQvsIu44SwCEe-dkB0PdK6AoPdy|Super Slicer - Probablemente el mejor programa para generar Gcode para tu impersora 3D]]
+  * [[https://www.youtube.com/watch?v=NU0aeQNQSek|Orca Slicer - Crear Perfil Hellbot Magna2]]
+</WRAP>
+===== Start/End Gcode para Anycubic 4max Pro =====
+==== Start Gcode ====
+Valores que trae el Orca ''2.2.0'' por defecto para la Anycubic 4Max.
+<code>
+M190 S[bed_temperature_initial_layer_single]
+M109 S[nozzle_temperature_initial_layer]
+PRINT_START EXTRUDER=[nozzle_temperature_initial_layer] BED=[bed_temperature_initial_layer_single]
+; You can use following code instead if your PRINT_START macro support Chamber and print area bedmesh
+; PRINT_START EXTRUDER=[nozzle_temperature_initial_layer] BED=[bed_temperature_initial_layer_single] Chamber=[chamber_temperature] PRINT_MIN={first_layer_print_min[0]},{first_layer_print_min[1]} PRINT_MAX={first_layer_print_max[0]},{first_layer_print_max[1]}</code>
+Código G inicial del barquito en mi Orca <code>
+; EXECUTABLE_BLOCK_START
+M73 P0 R137
+M201 X2000 Y2000 Z300 E5000
+M203 X300 Y300 Z12 E25
+M204 P2000 R5000 T2000
+M205 X9.00 Y9.00 Z0.20 E2.50 ; sets the jerk limits, mm/sec
+;TYPE:Custom
+M190 S50
+M109 S215
+PRINT_START EXTRUDER=215 BED=50
+; You can use following code instead if your PRINT_START macro support Chamber and print area bedmesh
+; PRINT_START EXTRUDER=215 BED=50 Chamber=0 PRINT_MIN=121.778,85.7173 PRINT_MAX=173.907,115.051
+G90
+G21
+M83 ; use relative distances for extrusion
+; filament start gcode
+M106 S0
+;LAYER_CHANGE
+;Z:0.2
+;HEIGHT:0.2
+;BEFORE_LAYER_CHANGE
+;0.2
+G92 E0
+G1 E-.9 F1500
+;_SET_FAN_SPEED_CHANGING_LAYER
+G1 X128.277 Y87.599 F18000
+G1 Z.6
+G1 Z.2
+G1 E.9 F1500
+M204 S300
+;TYPE:Skirt
+;WIDTH:0.5
+G1 F3000
+G1 X129.266 Y87.435 E.03658
+...
+</code>
+Código G inicial modificado para SuperSlicer FIXME <code>
+M190 S[first_layer_bed_temperature]; calienta cama y espera
+M104 S[first_layer_temperature]; calienta hotend sin esperar
+M280 P0 S160; reset 3dtouch
+G28 ; home all axes
+G29; nivelar
+G1 Z5 F5000 ; lift nozzle
+G1 Y100 F5000; Evita pinzas
+M109 S[first_layer_temperature]; espera hotend
+</code>
+Otro ejemplo FIXME <code>
+G90 ; use absolute coordinates
+M83 ; extruder relative mode
+M140 S[bed_temperature_initial_layer_single] ; set final bed temp
+M104 S150 ; set temporary nozzle temp to prevent oozing during homing
+G4 S10 ; allow partial nozzle warmup
+G28 ; home all axis
+G1 Z50 F240
+G1 X2 Y10 F3000
+M104 S[nozzle_temperature_initial_layer] ; set final nozzle temp
+M190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize
+M109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize
+G1 Z0.28 F240
+G92 E0
+G1 Y140 E10 F1500 ; prime the nozzle
+G1 X2.3 F5000
+G92 E0
+G1 Y10 E10 F1200 ; prime the nozzle
+G92 E0
+</code>
+El código que funcionaba con el Cura. 8-)
+<code>
+G21 ;metric values
+G90 ;absolute positioning
+M82 ;set extruder to absolute mode
+M107 ;start with the fan off
+G28 X0 Y0 ;move X/Y to min endstops
+G28 Z0 ;move Z to min endstops
+G1 X-3 Y40 ;Anycubic 4Max Pro Brush
+G1 X-3 Y5 ;Anycubic 4Max Pro Brush
+G1 X-3 Y40 ;Anycubic 4Max Pro Brush
+G1 X-3 Y5 ;Anycubic 4Max Pro Brush
+G1 Z5.0 F60 ;move the platform down 5mm
+G92 E0 ;zero the extruded length
+G1 F200 E3 ;extrude 3mm of feed stock
+G92 E0 ;zero the extruded length again
+G1 F60
+M117 Printing...
+G5
+</code>
+==== End Gcode ====
+Valores que trae el Orca ''2.2.0'' por defecto para la Anycubic 4Max.
+<code>
+PRINT_END
+</code>
+Código G final modificado para SuperSlicer FIXME <code>
+M104 S0 ; turn off temperature
+M140 S0 ; turn off bed
+M107 ;Turn off fan
+G1 X205 Y205 F5000; Aparta cabezal
+M84 ; disable motors
+</code>
+El código que funcionaba en el Cura. 8-)
+<code>
+M104 S0 ; turn off extruder
+M140 S0 ; turn off bed
+M84 ; disable motors
+M107
+G91 ; relative positioning
+G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+G1 Z+0.5 E-5 ;X-20 Y-20 F60 ;move Z up a bit and retract filament even more
+G90 ; absolute positioning
+G1 X140 Y215 Z200 F3000
+M84 ; steppers off
+G90 ; absolute positioning
+M300 P300 S4000
+</code>