====== [Anycubic 4max Pro] Configuración software ======

===== Cura =====

  * [[https://www.thingiverse.com/thing:3778487|4max pro Cura 4.1 profiles]] : {{ :doc:tec:print3d:p_4max_pro:profile:4max_pro_cura_4.1_profiles.zip |}}
  * [[https://github.com/mauricecyril/Anycubic-4MAX-PRO|mauricecyril - Anycubic-4MAX-PRO]]
  * [[https://marlinfw.org/meta/gcode/|Código Marlin]]

==== Start Gcode ====

Valores que trae el Cura ''4.6.2'' por defecto para la Anycubic 4Max.
<code>
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{speed_travel} ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{speed_travel}
M117 Printing...
G5
</code>

Cómo queda con modificaciones.
<code>
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 X-3 Y40 ;Anycubic 4Max Pro Brush
G1 X-3 Y5 ;Anycubic 4Max Pro Brush
G1 X-3 Y40 ;Anycubic 4Max Pro Brush
G1 X-3 Y5 ;Anycubic 4Max Pro Brush
G1 Z5.0 F{speed_travel} ;move the platform down 5mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{speed_travel}
M117 Printing...
G5
</code>


==== End Gcode ====

Valores que trae el Cura ''4.6.2'' por defecto para la Anycubic 4Max.
<code>
M104 S0 ; turn off extruder
M140 S0 ; turn off bed
M84 ; disable motors
M107
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 ;X-20 Y-20 F{speed_travel} ;move Z up a bit and retract filament even more
G28 X0 ;Y0 ;move X/Y to min endstops, so the head is out of the way
G1 Y180 F2000
M84 ;steppers off
G90
M300 P300 S4000
</code>

Cómo queda modificado.
<code>
M104 S0 ; turn off extruder
M140 S0 ; turn off bed
M84 ; disable motors
M107
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 ;X-20 Y-20 F{speed_travel} ;move Z up a bit and retract filament even more
G28 X0 ;Y0 ;move X/Y to min endstops, so the head is out of the way
G90 ; comienza movimiento por coordenadas absolutas
G1 Z200 F6000
M84 ;steppers off
G90 ; finaliza movimiento por coordenadas absolutas
M300 P300 S4000
</code>